Forum: Messages
04-12-24, 09:37 PM
|
Replies: 5
Views: 13,653
|
Forum: Messages
04-12-24, 10:02 AM
|
Replies: 5
Views: 13,653
|
Forum: Parts For Sale
04-12-24, 10:01 AM
|
Replies: 24
Views: 42,407
|
Forum: Messages
04-12-24, 09:52 AM
|
Replies: 5
Views: 13,653
Ryann
Wow you ingested something bad that...
Ryann
Wow you ingested something bad that destroyed the impeller of the turbo. you have to take that nut off the through stud. You can use an extremely long extension and the 9/16inch socket on the...
|
Forum: Messages
03-30-24, 11:22 AM
|
Replies: 3
Views: 13,668
|
Forum: Messages
02-04-24, 02:17 PM
|
Replies: 13
Views: 10,442
Yes it can if the seals are bad. Mine had a bad...
Yes it can if the seals are bad. Mine had a bad bore and I sleeved it. Make sure to undo the fittings to get the small pins out so you can pull the actuator rod out. The actuator rod has the seals on...
|
Forum: Messages
12-23-23, 09:29 PM
|
Replies: 22
Views: 27,623
I recently bleed mine very troublesome,...
I recently bleed mine very troublesome, eventually used my pressure pot from the calipers, installed a fitting where the vent plug is on the master cylinder ran a hose from it to a can, quite a bit...
|
Forum: Messages
12-03-23, 11:29 AM
|
Replies: 18
Views: 46,871
|
Forum: Messages
11-26-23, 01:23 PM
|
Replies: 6
Views: 17,167
|
Forum: Messages
11-26-23, 07:59 AM
|
Replies: 6
Views: 17,167
If I had to guess, over time the plastic cap...
If I had to guess, over time the plastic cap loosens up on the screws, and the whole balance weight assembly vibrates and cracks out the rib. The best way without a donor part is to make an oak form...
|
Forum: Messages
11-25-23, 06:04 PM
|
Replies: 6
Views: 17,167
Top rudder rib cracked
While installing my VG kit I found the RH rudder top rib cracked, p/n 1431002-13, rudder cap was loose. At least my parts airplane had a good one, cleaning, painting, and new nut plates will be...
|
Forum: Messages
11-23-23, 04:01 PM
|
Replies: 4
Views: 12,320
|
Forum: Messages
11-23-23, 03:59 PM
|
Replies: 4
Views: 12,320
Here are a few pics. The shaft for the driven...
Here are a few pics. The shaft for the driven gear is supposed to be press fit in the case with 271 loctite. The other pics are the new oil pump drive gear, oil pump gear, and new screen called out...
|
Forum: Messages
11-20-23, 04:50 PM
|
Replies: 4
Views: 12,320
|
Forum: Messages
11-20-23, 03:35 PM
|
Replies: 4
Views: 12,320
Engine oil leaks
So after having put over 105 hours on pushey in the last 1.5 years time to chase down oil leaks on the front engine.
Inlet check valve to turbo appeared to be cracked, taking it off the 1/8 pipe...
|
Forum: Parts Sources
11-08-23, 03:23 PM
|
Replies: 2
Views: 13,951
|
Forum: Parts For Sale
09-28-23, 12:07 PM
|
Replies: 24
Views: 42,407
|
Forum: Messages
08-19-23, 11:37 AM
|
Replies: 10
Views: 13,541
|
Forum: Messages
08-11-23, 09:14 AM
|
Replies: 10
Views: 13,541
All back together about .080-.090 of clearance...
All back together about .080-.090 of clearance that the pistons have to take up rotors are just a few thou below new and pads about 10 thou below new.
Still waiting on Parker, I still think that is...
|
Forum: Messages
08-09-23, 10:07 AM
|
Replies: 10
Views: 13,541
|
Forum: Messages
08-08-23, 10:13 PM
|
Replies: 10
Views: 13,541
Randy
I have all the manuals, Parker, took them...
Randy
I have all the manuals, Parker, took them apart to reseal, they were leaking, pistons were out then also. Not my first rodeo as I am an A&P and IA, old pads same thickness as the the new pads....
|
Forum: Messages
08-08-23, 09:17 PM
|
Replies: 10
Views: 13,541
|
Forum: Messages
08-08-23, 04:15 PM
|
Replies: 10
Views: 13,541
Heavy duty brakes
Just resealed my calipers 30-69B heavy duty brakes. Pads are about the same thickness as new not changing those have them though. Putting the calipers back on the wheel, disc thickness is within...
|
Forum: Messages
07-30-23, 08:21 PM
|
Replies: 2
Views: 7,189
|
Forum: Messages
07-19-23, 09:44 PM
|
Replies: 24
Views: 25,472
|