Forum: Parts For Sale
11-08-19, 08:35 AM
|
|
Replies: 3
Views: 12,540
landing gear collapse
After dealing with the bureaucracy and ferrying the plane home, we found the rotary gear actuator cylinder had cracked all along the casting seam flushing out all the hydraulic fluid.
Don't know if...
|
|
Forum: Messages
09-11-19, 04:59 AM
|
|
Replies: 3
Views: 24,009
Insurance WARNING - read and heed
After gear collapse on landing and some damage, it looks like Avemco will deny any claim based on somewhat small obscure definition that says they define "flight" as including all phases of takeoff...
|
|
Forum: Parts For Sale
09-07-19, 05:39 AM
|
|
Replies: 3
Views: 12,540
1972 Serial No. 00025 T337G. Normal approach,...
1972 Serial No. 00025 T337G. Normal approach, downlock thunk didn't seem right ( but had green light) so did a tower flyby. Tower said 3 down ,looked normal, cleared to land. Touchdown seemed normal,...
|
|
Forum: Parts For Sale
09-05-19, 05:37 AM
|
|
Replies: 3
Views: 12,540
right landing gear collapse
Anyone had or heard of one leg of landing gear collapsing after landing with down lock light (green) lit and tower fly by confirming gear down appearing normal?
|
|
Forum: Messages
07-03-19, 11:24 AM
|
|
Replies: 4
Views: 18,111
Pennycap wire
I found a good article on trobleshooting pennycap. It was working fine until I got ACF50 corrosion treatment when both guages went to zero. The oil is apparently somewhat conductive or it change the...
|
|
Forum: Messages
07-01-19, 01:24 PM
|
|
Replies: 4
Views: 18,111
Cabling for pennycap system
Anyone know what the cable is hooking up the sensors to the controller?
I had my 337G corrosion ACF50 treated and fuel guages quit, Assume the cabling or connections were affected capacitance wise....
|
|
Forum: Messages
01-07-19, 04:50 AM
|
|
Replies: 1
Views: 7,581
73' P337 tachometer on the fritz
Anyone have any luck with someone doing repairs? The shops I've contacted say any tach but this one. Found a used one but it was DOA.
|
|
Forum: Messages
06-18-18, 10:46 AM
|
|
Replies: 3
Views: 15,320
|
|
Forum: Messages
06-18-18, 08:06 AM
|
|
Replies: 3
Views: 15,320
Chains for lower clamshell door fixed
Finally found simple solution to door chains getting caught in door- I don't know if any one else has that problem but having to lean over unfamiliar passengers to manipulate the rear chain so it...
|
|
Forum: Parts For Sale
05-11-18, 09:09 AM
|
|
Replies: 2
Views: 18,897
|
|
Forum: Parts Sources
03-15-18, 06:11 AM
|
|
Replies: 2
Views: 16,757
'73 P337 window trim (plastics)
I located the window plastic 1515025-3 I needed at :
Don Nieser
Commodore Aerospace Corp
405-503-4686
A good source for many things Skymaster.
|
|
Forum: Parts Sources
03-14-18, 06:22 AM
|
|
Replies: 2
Views: 16,757
Looking for '73 P337 window trim 1515025-3
Renovating cabin now need plastic window trim panel. Replaced most plastic either from Cessna (ridiculous prices) or Plane Plastics - they have the non pressurized stuff. Cessna is make to order for...
|
|
Forum: Mechanics and Service Providers
02-13-18, 07:25 AM
|
|
Replies: 0
Views: 28,652
Aero Resources in Columbia -
Located just East of Modesto and the central valley of California, Aero Resources has deep (20years) with all types of aircraft including a lot of work on Skymasters. Nice people and reasonable...
|
|
Forum: Parts Sources
02-13-18, 07:15 AM
|
|
Replies: 0
Views: 13,561
|
|
Forum: Mechanics and Service Providers
02-11-18, 01:21 PM
|
|
Replies: 3
Views: 35,911
Aero Resources in Columbia has done extensive...
Aero Resources in Columbia has done extensive work on my '72 P337 for the past three years and know them inside out and are 'small town' reasonable, friendly and helpful. Phone is 209.533.4543
|
|
Forum: Messages
02-07-18, 07:23 AM
|
|
Replies: 12
Views: 24,782
337 renovation
Yeah, lots of work but a light at the end of the tunnel. A lot of work over the past couple of years went into replacing leaking hydraulic seals, leaking rocker covers, leaking push rod seals,...
|
|
Forum: Messages
02-05-18, 12:31 AM
|
|
Replies: 12
Views: 24,782
Here are some pictures of the interior. The...
Here are some pictures of the interior. The wiring was a mess and am rewiring some and removing vast amounts of dead wire. The plastic is almost all new and painted very light yellow. It was brittle...
|
|
Forum: Messages
02-04-18, 04:00 PM
|
|
Replies: 12
Views: 24,782
|
|
Forum: Messages
02-03-18, 09:08 AM
|
|
Replies: 12
Views: 24,782
Renovating neglected P337
Two years of fixing one thing and then another. Major effort for the past 5 months nearing completion. Interior plastics replaced or repaired and painted. New soundproofing especially rear bulkhead -...
|
|
Forum: Messages
01-07-18, 09:53 AM
|
|
Replies: 9
Views: 20,170
Jpi 960
I'm installing a 960 in a P model and finding some issues with probe placement on the fron engine passenger side. Mine is a G mode pressurized. Wondering if you had the same problem. If so, how was...
|
|
Forum: Messages
01-04-18, 05:41 AM
|
|
Replies: 0
Views: 10,599
JPI 960 engine monitor for P337G
Anyone installed the 960 in a P model? I'm finding the installation on the front engine is a real problem in keeping to a constant distance from the cylinder of 2 to 4 inches especially on the front...
|
|
Forum: Messages
01-04-18, 05:32 AM
|
|
Replies: 5
Views: 17,958
|
|
Forum: Messages
01-02-18, 10:46 AM
|
|
Replies: 5
Views: 17,958
Anyone have experience "soundproofing" T337P
Like to find out what worked and what didn't. Also cant seem to get clear answer on what is best - fiberglass(in there now), open cell foam, closed cell form, foil with bubble plastic inside, Any...
|
|
Forum: Parts For Sale
09-20-17, 10:30 AM
|
|
Replies: 12
Views: 42,684
|
|
Forum: Messages
08-16-17, 04:46 PM
|
|
Replies: 5
Views: 19,877
|
