Skymaster Forum  

Go Back   Skymaster Forum > Search Forums
Register FAQ Members List Calendar Today's Posts

Showing results 1 to 13 of 13
Search took 0.00 seconds.
Search: Posts Made By: pilotpat
Forum: Messages 08-29-23, 05:16 AM
Replies: 2
Views: 20,703
Posted By pilotpat
We had a similar issue (ours does not have the...

We had a similar issue (ours does not have the gear door mod). It turned out to be the pressure switch (basically a plunger pushed by the hydraulic fluid to actuate a microswitch). The fluid sealing...
Forum: Messages 01-12-23, 04:57 AM
Replies: 4
Views: 29,684
Posted By pilotpat
MEL-28-02 - Fuel – Fuel Strainer Inspection...

MEL-28-02 - Fuel – Fuel Strainer Inspection (https://support.cessna.com/custsupt/contacts/pubs/ourpdf.pdf?as_id=54965) (Models: 337, T337, F337, FT337, FTB337, P337) Compliance: M - Date: 01/05/2023...
Forum: Messages 12-04-17, 05:40 AM
Replies: 10
Views: 19,741
Posted By pilotpat
Thanks! Those locations should work for the...

Thanks! Those locations should work for the Insight as well, and allow reuse of the existing hose for one of the legs. Is the white wire connecting to a temperature probe?
Forum: Messages 11-28-17, 07:11 PM
Replies: 10
Views: 19,741
Posted By pilotpat
Jeff, in the end we did not go ahead with G4...

Jeff, in the end we did not go ahead with G4 install but will at some time. The recommendation was to replace the hose going to the flow distributor with two shorter pieces and have the fuel flow...
Forum: Messages 11-09-17, 05:35 AM
Replies: 14
Views: 28,181
Posted By pilotpat
Here's a pic taken looking down through the gap...

Here's a pic taken looking down through the gap previously mentioned (the "20" is the radar range knob). The brass lever has to be rotated up and the thole thing pulled up and out. There is a...
Forum: Messages 11-08-17, 07:43 AM
Replies: 14
Views: 28,181
Posted By pilotpat
This picture should allow some orientation, note...

This picture should allow some orientation, note the friction lock at the top. The dipstick is behind my shoulder, and the hatch in the panel (removed) is about where the blue hydraulic fittings are....
Forum: Messages 11-08-17, 07:33 AM
Replies: 14
Views: 28,181
Posted By pilotpat
Tom, if able, look down though the gap above the...

Tom, if able, look down though the gap above the radar unit and below the trim wheel (a light will be needed). At the bottom front roughly in the middle is the top of the dipstick, which on ours is a...
Forum: Messages 10-24-16, 05:51 AM
Replies: 9
Views: 17,218
Posted By pilotpat
Something like this?:...

Something like this?: http://www.newark.com/vishay/tva1315/aluminum-electrolytic-capacitor/dp/18F975
Forum: Messages 10-21-16, 06:00 AM
Replies: 9
Views: 17,218
Posted By pilotpat
Any chance there is no power to the circuit, like...

Any chance there is no power to the circuit, like a broken power or ground wire somewhere? Would be consistent with no unit working.
Forum: Messages 10-20-16, 06:03 AM
Replies: 1
Views: 11,005
Posted By pilotpat
FWIW the hydraulic power pack diode (DIODE AY...

FWIW the hydraulic power pack diode (DIODE AY MOTOR PWR PACK 1270717-2) uses 1N5060.
Forum: Messages 08-18-16, 07:06 AM
Replies: 10
Views: 19,741
Posted By pilotpat
Insight Flow sensors onto an IO-360-GB

This is research for a G4 Twin engine monitor install.
Anyone have experience (and possibly pictures) of installing Insight Avionics flow sensor (http://www.insightavionics.com/tf500.htm)s onto an...
Forum: Messages 04-05-16, 02:09 PM
Replies: 2
Views: 9,197
Posted By pilotpat
Just wondering if there is a electrical...

Just wondering if there is a electrical equivalent 1N???? spec for this diode. I am curious as I have a funny feeling they may be seeing way more voltage when the contactor switches than they are...
Forum: Messages 01-23-16, 09:10 AM
Replies: 9
Views: 19,078
Posted By pilotpat
This is a Skyvette http://skyvette.com/. Replace...

This is a Skyvette http://skyvette.com/. Replace IO-360s with Corvette engines. A work in progress, only one made.
Showing results 1 to 13 of 13

 
Forum Jump

All times are GMT -4. The time now is 07:29 PM.


Powered by vBulletin® Version 3.6.9
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.