|
|
|||||||
| Register | FAQ | Members List | Calendar | Today's Posts | Search |
 |
| Thread Tools | Rate Thread | Display Modes |
|
#2
11-05-18, 12:54 PM
|
|||
|
|||
|
I'm not familiar with the fuel caps on the 65 model but on my 1973 337G model I was able to replace all the rubber on my fuel plugs from a company in Wisconsin....
Petersen Products Co, LLC 421 Wheeler Avenue P.O. Box 340 Fredonia, WI 53021-0340 Phone: 262-692-2416 petersenproducts.com Search "lever type expandable rubber plugs" The plugs look curiously similar to the factory rubber fuel plugs that were in my C337 but the plugs are not vented. I measured the size of the fuel port and purchased a few different sizes because I was never happy with the fit of the original Cessna plugs. Off hand I cannot recall the dimension I ended up using but I was able to find a very snug fit that I am very confident in for not much money, even though I ended up with plugs I did not use. It was not worth the effort to return them and the folks there were very helpful. I simply disassembled the plug that I purchased and used the neoprene rubber that came with the new plug. The rubber was all I was after. They would not sell me just the rubber only the entire cap assembly. I used the new rubber on the original Cessna vented cap and all is right with the new plug. Good Luck..... Ed 
|
|
#3
11-06-18, 08:39 AM
|
||||
|
||||
|
I don't see that these are approved for 337's but is this what you are referring too?
https://monarchcaps.com/
__________________
Herb R Harney 1968 337C Flying the same Skymaster for 47 years Last edited by hharney : 11-06-18 at 08:41 AM.
|
|
#4
11-09-18, 08:28 AM
|
||||
|
||||
|
Kind Of
Didn't find the lever type plugs.
Evidently John Russman mentioned they "Thermos Plug with Lever Style" has an AD or SB and there is a replacement kit sold by someone. Once I learn who I'll post it. Herb, I believe the Monarch ones are close to what John mentioned. I'll need to find the exact replacements.
|
|
#5
11-09-18, 12:36 PM
|
||||
|
||||
|
This AD is replacement of caps for venting purposes
http://rgl.faa.gov/Regulatory_and_Gu...2?OpenDocument
__________________
Herb R Harney 1968 337C Flying the same Skymaster for 47 years
|
|
#7
11-11-18, 01:50 PM
|
||||
|
||||
|
Quote:
https://www.controller.com/parts/air...rch&pst=starts http://cessnadirect.com/product-sear...uery=SK337-40C
__________________
Herb R Harney 1968 337C Flying the same Skymaster for 47 years Last edited by hharney : 11-11-18 at 01:53 PM.
|
|
#8
11-21-18, 06:30 PM
|
|||
|
|||
|
Quote:
|
|
#9
11-24-18, 04:02 PM
|
||||
|
||||
|
Thermos Style Fuel Caps
Larry I have the replacement kit from Cessna to change from old style to the vented caps, like on single engine Cessnas. I have the blue print that goes with the install kit. The only parts I don't have are three of the humped fuel cap covers, but you get them from Don Nieson for about $30-40 each (used). This kits are fairly easy to install and only needs a logbook entry-no Form 337 required. If interested e-mail me at bstory@pa.rr.com or call 814-673-6863c
BILLS Last edited by cessnadriver : 11-24-18 at 04:03 PM. Reason: forgot something
|
Linear Mode
