Skymaster Forum  

Go Back   Skymaster Forum > Messages
Register FAQ Members List Calendar Search Today's Posts Mark Forums Read

Reply
Thread Tools Rate Thread Display Modes
  #1  
Unread 05-04-08, 03:34 AM
Skymaster337B's Avatar
Skymaster337B Skymaster337B is offline
Registered User
 
Join Date: Jun 2004
Location: New Mexico
Posts: 508
Skymaster337B is an unknown quantity at this point
Angry Shimmy Strut

Any easy way to service the nose wheel shimmy strut? Very difficult location for my hands to access.
Reply With Quote
  #2  
Unread 05-04-08, 07:46 AM
skymstr02's Avatar
skymstr02 skymstr02 is offline
Ace of the Atmosphere
 
Join Date: Apr 2002
Location: Madison, MS
Posts: 329
skymstr02 is an unknown quantity at this point
Usaully if it needs servicing, a seal has gone out, so it would need to be removed, repaired, serviced and reinstalled anyway.
Reply With Quote
  #3  
Unread 05-04-08, 12:39 PM
n9121x@aol.com n9121x@aol.com is offline
Registered User
 
Join Date: Apr 2008
Location: KCCB
Posts: 5
n9121x@aol.com is on a distinguished road
the only real safe way is take the weight off the nose gear, and someone with a somewhat skinny enough arm, reach up through the inspection hole to gain access to the servicing valve...I think the book calls out for between 35 and 40 pounds....I typically put enough air into it to where the scissors look like a strecthed out "V"...if you put too much air in the strut, you will not be able to steer

Wes Grady
KCCB hangar 208
Reply With Quote
  #4  
Unread 05-04-08, 02:31 PM
Pete Somers Pete Somers is offline
Registered User
 
Join Date: Jul 2002
Location: Yorkshire. UK.
Posts: 229
Pete Somers is an unknown quantity at this point
We used to put the nose on a jack and lift clear of the ground, chock behind both main wheels and put the u/c lever up and pump the gear until the nose gear unlocks. The shimmy damper is easy to get to then. The mains cannot unlock and go up due to the weight of the airplane.

Pete
Reply With Quote
  #5  
Unread 05-04-08, 04:54 PM
skymstr02's Avatar
skymstr02 skymstr02 is offline
Ace of the Atmosphere
 
Join Date: Apr 2002
Location: Madison, MS
Posts: 329
skymstr02 is an unknown quantity at this point
Are we talking shimmy dampner or nose strut here? The dampner is on the top of the gear.
Reply With Quote
  #6  
Unread 05-04-08, 11:02 PM
Skymaster337B's Avatar
Skymaster337B Skymaster337B is offline
Registered User
 
Join Date: Jun 2004
Location: New Mexico
Posts: 508
Skymaster337B is an unknown quantity at this point
I asked about the nose wheel shimmy...sorry for any confusion.
Reply With Quote
  #7  
Unread 05-05-08, 08:08 AM
skymstr02's Avatar
skymstr02 skymstr02 is offline
Ace of the Atmosphere
 
Join Date: Apr 2002
Location: Madison, MS
Posts: 329
skymstr02 is an unknown quantity at this point
Before you tackle the shimmy dampner, you need to do a few basic troubleshooting items first:
  • Make sure that the nose tire is inflated to specs.
  • Make sure that the nose wheel bearings are no defective or the axle bolt is too loosed.
  • Make sure that the nose tire is within balance.
  • Make sure that the nose gear torque links do not have excessive play.
  • Make sure that you don't have a warped main gear brake disc.
This will eliminate some of the more common causes of nose gear shimmy before you tackle the dampner. Usually the Skymaster shimmy dampners work for many years without any difficulty.
Reply With Quote
  #8  
Unread 05-05-08, 09:50 AM
Ernie Martin's Avatar
Ernie Martin Ernie Martin is offline
Administrator
 
Join Date: Apr 2002
Location: Miami, Florida
Posts: 989
Ernie Martin is an unknown quantity at this point
However, I have found an easier indicator that it is the dampner: if it happens only when the dampner is hot. I've had to overhaul the dampner once on each of my two Skymasters and each time there was no shimmy on the first takeoff of the day (especially if it's a cool morning) and shimmy when you landed on a hot day (I'm in Miami) or if you took off soon after a hot landing (remember that the dampner is close to the front engine). One other thing: if the housing is sound, your A&P can rebuild it using the seals shown in the parts catalog.

Ernie
Reply With Quote
  #9  
Unread 05-05-08, 10:16 PM
Kim Geyer Kim Geyer is offline
Registered User
 
Join Date: May 2002
Location: Bahama, NC
Posts: 289
Kim Geyer is an unknown quantity at this point
You can also connect your tow bar and turn the nose gear left and right, if the dampener is low on fluid it will make a squirting sound.
Kim
Reply With Quote
  #10  
Unread 05-07-08, 03:21 PM
Jim Rainer's Avatar
Jim Rainer Jim Rainer is offline
Jim Rainer
 
Join Date: Apr 2002
Location: Memphis, TN
Posts: 163
Jim Rainer is an unknown quantity at this point
I had this problem about a year ago and my mechanic convinced me to change the front tire first and if that didn't work, he'd pay for it. It worked! The old tire looked OK but his knowledge of the problem told him that he had worked on lots of shimmy dampners first then find out all that was needed was a new tire!
Reply With Quote
  #11  
Unread 04-28-22, 11:38 PM
AirCzar AirCzar is offline
Registered User
 
Join Date: Apr 2022
Location: USA
Posts: 2
AirCzar is on a distinguished road
Replacing the shimmy dampener

Well after researching the issue here and talking to a number of folks that basically shrugged their shoulders the most useful blog was the suggestion to raise the nose gear.. a bit. So today we jacked the aircraft (we had to anyway for the annual inspection) put the gear handle up with the circuit breaker pulled and then used the breaker to raise the nosewheel to about a 45 degree angle I had already removed the front wheel to balance it Sho nuff this gives you room to get your hand and side cutters up to remove the cotter keys and then the nuts. Front bolt no problem to remove from within the engine compartment. The rear bolt was tougher. we turned the wheel all the way to the left (after disengaging the centering mechanism) and managed to raise the bolt just enough to clear the dampener ear. Now to rebuild the dampener, put it back in and enjoy installing new cotter pins!!! Easy huh??
Peter
Reply With Quote
  #12  
Unread 06-05-22, 12:02 PM
Dan schultz Dan schultz is offline
Registered User
 
Join Date: Nov 2018
Location: Ohio
Posts: 127
Dan schultz is on a distinguished road
Balancing the tire assembly dynamically helps a lot also. I have an older Snap On car tire balancer that I modified, works great. Instructions are on the web. Do a search of balance aircraft tires.

Dan
Reply With Quote
Reply


Thread Tools
Display Modes Rate This Thread
Rate This Thread:

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

vB code is On
Smilies are On
[IMG] code is Off
HTML code is Off
Forum Jump


All times are GMT -4. The time now is 12:38 AM.


Powered by vBulletin® Version 3.6.9
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.